Full_Big_Boy_Kit
Base_Kit_BlueX_Kit2X_Kit1BaseKit2BaseKit1Streamline2Streamline1Drill_LocatorUndersideIMG_8330IMG_8273Belt_routingIMG_8281Prusa4Prusa_Extruder_NEW_2018BLUEIMG_8279IMG_8288IMG_8292IdlerIMG_8290IMG_8293bltouchmountIMG_8295106mm Y rod spacing from mount to edge of frame both sidesZ_MotorZ_TopY_RodsY_IdlerX-MotorRear_AssemblyIMG_7700X-EndstopX_EndstopBump

Big Boy Blue Cr10/s Conversion Full Kit

$134.99

96 items sold

This conversion kit for the CR10/s 4 & 5 is the full blown kit including the Full Base Kit, Full Y Axis Kit and the Streamline Extruder Body. Everything you need printed in Premium PETG for one low price.

Included:

  • Big Boy Blue Base Kit
  • Y Axis Kit
  • X Kit
  • Streamline Extruder Body and cooling fan ducting

These printed parts for this mod will allow you to convert your cr10/s to a direct drive unit with 12mm Liner rods for the Y axis and 8mm rods for the X axis. All printed parts seen in illustrations for your color selection are included in this mod kit. With this mod installed you will take your printing quality to the next level. Some parts may also be printed in ABS where required if applicable.

Included below are the sources for the other parts needed to complete this mod.

Linear Rods

  • (2) 12mm x 500mm Linear Rods Y Axis LINK
  • (2) 380mm x 8mm Linear Rods X Axis LINK
  • (2) 530mm x 8mm Linear Rods Z Axis LINK
  • (1) MK8 Hobbed Extruder Gear LINK
  • 6-8 ft GT2 Belt for X and Y axis LINK | Alternate LINK
  • (7) LM8UU Linear Bearings LINK
  • (1) 624zz Bearing for extruder LINK
  • (4) SCS12UU Linear Motion Ball Bearing, For Y Axis LINK
  • (2) 20 tooth idler pulley for X and Y LINK

T Nuts and bolts and other

    • (30) M4 X 10 Socket Head Cap Screw LINK
    • (14) M4 X 20 Socket Head Cap Screw LINK
    • (8) M4 X 30 Socket Head Cap Screw LINK
    • M4 T-Nuts Packet LINK
    • 1/2 in Braided Wiring Sleeve LINK
    • Aluminum Spacers to replace spring bed mounts. LINK
    • 14 Gauge Silicone Wire Not required but nice if you plan on relocating your PSU LINK
    • * Braided Cable Wrap Various Color Selection LINK

Wires

If you need some appropriate wire for this Mod Amazon has a good deal on 30awg wire. A spool with various colors and more than enough for this and many other future Mods LINK

Also if some of the links below no longer are valid try here.

Notes:

  • You can easily recycle all stepper motors however I suggest a lighter Pancake Stepper for the extruder.
  • Wiring endstops require only 2 wires. Use only the outside terminals on each endstop. If your endstop functions opposite than you expect simply swap the wires to a reverse connection from they way they were.
  • In my illustration shown in photos I soldered wires the the endstop after verifying they were connected properly and applied Yellow heat shrink to the wire ends.
  • It's helpful to print out a pair of the bed mount jig's to assist in aligning holes that are to be drilled. I suggest indicating 1 hole for each bearing for the bed one at a time. Mount the bearing for all 4 locations then with the rods for the bed loose but in place mounted to the frame, square things up and manually slide the bed back and forth allowing the rods to position the rod mounts on the frame. It may also be helpful to secure one side of the bed rod mounts to the frame after measuring the distance. Once one side is secure and the opposite side mounted but loose then run your bed back and forth allowing the loose side to move into place where there is the very least resistance possible. Once complete then you can secure the rod mounts to the frame.
  • It is only necessary to secure each bearing to the bed mount with 2 screws each. Using 4 will make things more difficult to align as they will tend to fight each other as you secure them in place.
Clear selection

Product Description

Big Boy Blue Cr10/s Conversion Full Kit
4.7 (93.75%) 16 votes

This conversion kit for the CR10/s 4 & 5 is the full blown kit including the Full Base Kit, Full Y Axis Kit and the Streamline Extruder Body. Everything you need printed in Premium PETG for one low price.

Notice: This is a printed parts kit only. Hardware not included.

Additional Information

Weight 25 oz
Color

Blue

Reviews

There are no reviews yet.

Be the first to review “Big Boy Blue Cr10/s Conversion Full Kit”

Positive SSL